Apr 2, 2015 - But I can't get it to boot up with the TV as monitor. It's an early “HD Ready” TV by Bush with a VGA port for PC at the back. Ignoring the message which says 'Please note that some drivers require a full graphical boot. Apr 29, 2018 - Hello, I purchasded a HP Pavillion 15-n031sa last week and I am having problems connecting it to my Bush 42' wide screen LED TV (model no.

Hi!, Thanks for stopping by the HP Support Forums! I understand that you are unable to get audio from bush TV using HDMI cable. As you mentioned that when you connect the same cable to your LGTV audio works fine. This indicates it could be a problem with your TV.

Check few settings mentioned below on your TV. Make sure TV is not muted. Make sure the TV is not set to SAP (secondary audio protocol) Make sure TV input is correct (someone may have accidentally pressed the “aux” input button or similar causing the TV to use an input with no sound going to it) Make sure there is not a pair of headphones connected to the TV audio out jack on the side or front of your TV. Check all of the cables that are connected to the back of your TV.

(it is possible the TV was moved slightly and a cable has become disconnected or loose) If you have a receiver or surround sound connected to your TV, turn it on and see if you get sound coming from the external speakers. Turn off the TV, cable box, and anything else connected to the TV. Sometimes turning everything off and then back on can fix the problem. If using an “S” video cable into an input on the back of your TV, these cables carry no sound, just video, so make sure you connect an audio cable too. Hook up an external device to the “TV audio out” input.

This will be the test to see if it is a TV circuit board malfunction or the speakers are faulty on your TV. If you are connected to a satellite box, use the included remote and go into the “menu”. Check to make sure sound settings are set correctly.

Hope to hear from you soon! Have a great day!:). Hi!, thanks for the response. Please try few steps mentioned below.

Open the Device Manager in Windows 10. Vetkodrobilka svoimi rukami. Navigate to Sound, video, and game controllers.

Now connect your PC to TV using HDMI connection. This will show some “HDMI Audio” related driver under the above section. Now right-click that item and UNINSTALL it. Now right-click Sound, video, and game controllers and select “Scan for hardware changes“. This will install a typical driver which is something like this – “Device with HDMI AUDIO OUTPUT SUPPORT”. Now your Windows 10 HDMI audio problem should be resolved.

If the issue still persists please provide the product number of your PC. I will try to find the best drivers for your laptop. Hope to hear from you soon!

Hi guys, I hope you can tell me where I am going wrong. I have onboard Nvidia 8200 graphics, with a monitor connected to the VGA socket and a TFT TV connected to the DVI socket with a DVI to HDMI cable. The TV is switched to HDMI input, but displays only a blank blue screen. Windows [XP] display properties recognises the TV as a plug and play monitor. The Nvidia control panel recognises it correctly as a 26' TFT-TV. It makes no difference whether I use clone mode or multiple display mode, or whether I have the TV as primary or secondary display. I have stepped through every setting in the control panel [from 480p to 1080i].

Whatever the settings, there is no signal. The TV works using a different graphics card and RCA TV-out, but of course the picture quality is less than optimal. Windows Xp Pro SP3 K10N78M Pro motherboard with onboard Nvidia 8200 graphics driver version 6.

The TV is a Bush idlcd26tv27hd Thanks for any help you can offer. Oh, if anyone has a manual for this TV I would be super-grateful!

It makes no difference whether I use clone mode or multiple display mode, or whether I have the TV as primary or secondary display. I have stepped through every setting in the control panel [from 480p to 1080i]. Whatever the settings, there is no signal. Paddywhack, Hello. I always start with the simplest, and proceed from there.

In your Nvidia Control Panel 'Change resolution Screen ' Do you have HDMI enabled? If you do post back and will go from there. Regards Fred PS: You might want to check out this link to make sure that your DVI HDMI cable is the correct one.

Hi Fred, thanks for the reply. The good news is that it is now working. The bad news is that I don't have a clue why! Last night I reverted to using the PCI-E graphics card and RCA connection, under pressure to stop messing about and put a movie on.

In my hurry I forgot to change the primary adaptor in the BIOS from onboard to PCI-E. To my astonishment, the boot up screen then displayed on the TV [and not on either the other screen connected to the onboard graphics, nor on the screen connected to the PCI-E]. For a glorious 10 minutes I had both the onboard and the PCI-E card working at the same time, which I didn't think was possible, and windows display properties reporting 4 screens [2 of which were connections to the TV, one from each graphics source]. Then I had a BSOD 7E, which was only resolved by uninstalling both graphics drivers, then reinstalling the PCI-E driver. The tale picks up today with me doing things in the right order, uninstalling the PCI-E driver and installing the onboard one, changing the BIOS setting, and it all works fine now.